asphalt standard according to astm

asphalt standard according to astm

POWERply Standard FR - tremcoroofing.com

Standard FR is also asbestos free. POWERply Standard FR was formerly known as THERM MB LTD. POWERply Standard FR exceeds ASTM D 6163-00, Type I, Grade G. Basic Use:POWERply Standard FR is designed for application in both hot and cold applied roof sys-tems

Learn More

Dynamic Shear Rheometers SmartPave for Asphalt

For standard asphalt tests according to AASHTO, ASTM, DIN EN, and FGSV Temperature range: -30 °C to 120 °C Upgradeable to all standard rheological tests With the modular compact rheometer MCR 502S rounding off the portfolio, Anton Paar rheometers meet all

Learn More

ASTM D3381/D3381M - Standard Specification for Viscosity

For asphalt binders graded by penetration at 25 °C [77 °F], see Specification D946/D946M. If needed, volume corrections for asphalt binders should be made according to Practice D4311/ D4311M. The values stated in either SI units or inch-pound units are to

Learn More

Shingle specification

an ASTM International test method in 2005. The current edition is ASTM D7158-11. According to ASTM D7158, asphalt shingles are classified as Class D if they pass at a basic wind speed of 90 mph, Class G if they pass at a basic wind speed of 120 mph or Cla

Learn More

ASTM-D7173 | Standard Practice for Determining the

1.1 This practice describes a laboratory procedure for determining the tendency of polymer to separate from polymer modified asphalt under static heated storage conditions. The results of testing on material prepared according to this practice may be used

Learn More

Standard penetrometers, Bitumen testing equipment, Controls

Digital standard penetrometer complete with micrometer vertical adjustment 81-B0101/E Digital electronic semi-automatic penetrometer complete with micrometer vertical adjustment and adjustable electronic timer of the fall time, according to EN 1426, ASTM

Learn More

SECTION 401 ¾ ASPHALT PLANT REQUIREMENTS

asphalt binder scales that conform to Subsection 401.02.02 B). When metering the quantity of asphalt binder, check the delivery of the meter by actual weight. For drum and continuous mixing plants, calibrate the asphalt binder delivery system and metering

Learn More

Road Standards and Paving Standards - ASTM International

Road Standards and Paving Standards ASTM's road and paving standards provide the specifications and test methods pertinent to the material, physical, mechanical, performance, and application requirements of road surfaces and pavements.

Learn More

Standard Specification for Viscosity-Graded Asphalt Cement

The purchaser shall specify the applicable table of limits. In the event the purchaser does not specify limits, Table 1 shall apply. For asphalt cements graded by penetration at 77°F (25°C) (see Specification D 946). If needed, volume corrections for asph

Learn More

ASTM D7173-14 - Standard Practice for Determining the

The results of testing on material prepared according to this practice may be used as a guideline when formulating products or to establish field handling procedures. Large differences in test results between top and bottom specimens indicate that there i

Learn More

ASTM D5361/D5361M - 16 - Standard Practice for Sampling

Purchase your copy of ASTM D5361/D5361M - 16 as a PDF download or hard copy directly from the official BSI Shop. All BSI British Standards available online in electronic and print formats. ASTM D5361/D5361M - 16 - Standard Practice for Sampling Compacted

Learn More

ASTM D6373 - Standard Specification for Performance Graded

For asphalt cements graded by viscosity at 60°C see Specification D3381. NOTE 2-AASHTO R 29 provides non-mandatory information for determining the performance grade of an asphalt binder. The values stated in SI units are to be regarded as standard. No oth

Learn More

Tests Applied on Bitumen | Procedure of Tests on Asphalt

Ductility Test on Asphalt . The ductility test (ASTM D113) measures the distance a standard asphalt sample will stretch without breaking under a standard testing condition (5 cm/min at 25 °C). It is generally considered that an asphalt with a very low duc

Learn More

ASTM-D6307 | Standard Test Method for Asphalt Content of

1.1 This test method covers the determination of asphalt content of asphalt mixture and asphalt pavement samples by removing the asphalt cement in an ignition furnace. The means of sample heating may be the convection method or direct irradiation method.

Learn More

SUPERPAVE ASPHALT CONCRETE END PRODUCT SPECIFICATION

SUPERPAVE ASPHALT CONCRETE END PRODUCT SPECIFICATION (EPS) NOVEMBER 2017 4 • ASTM D3665, Standard Practice for Random Sampling of Construction Materials • ASTM D4791, Standard Test Method for Flat Particles, Elongated Particles, or Flat and Elongated Part

Learn More

Leave a comment